Mobifix

You plug in your iPhone and… nothing. No charging symbol, or it charges painfully slowly, or it cuts in and out. Before you assume the worst, know this: the most common cause of an iPhone that won't charge isn't a broken port — it's lint packed into the charging port . This guide takes you through every fix in order, from the 30-second checks to when you genuinely need a repair. Start with the quick checks Try a different cable and adapter. Cables fail internally far more often than ports. Test with a known-good Apple or MFi-certified cable. Try a different power source. Swap the wall outlet, and try a wall adapter instead of a laptop USB port — laptops and some car chargers deliver too little power. Force restart the iPhone. Press and release Volume Up , press and release Volume Down , then press and hold the Side button until the Apple logo appears. This clears software freezes that block charging. Clean the charging port (the #1 real fix) Lint, ...

  Is your iPhone battery draining faster than it used to? Whether it's dropping 20% while sitting in your pocket or dying by mid-afternoon, fast battery drain is one of the most common iPhone problems — and most of the time you can fix it yourself in a few minutes. This guide walks through 12 proven fixes, from quick settings tweaks to knowing exactly when a battery replacement is the real answer. First, check your battery health Before changing any settings, find out whether the problem is software or the battery itself. Go to Settings → Battery → Battery Health & Charging and look at Maximum Capacity . Above 85% – the battery is fine; your drain is almost certainly a software or settings issue (keep reading). 80–85% – noticeable wear; optimising settings will help, but you'll feel the difference. Below 80% – iOS considers the battery worn. If you also see a "Service" message, a battery replacement is the real fix. Fi...

Samsung Galaxy Star S5282 Usb Charging Problem Solution Jumper Ways Samsung Galaxy Star S5282 usb charging solution, Samsung Galaxy Star S5282 usb not recognised not detected  

Samsung Google Nexus S i9020 Usb Charging Problem Solution Jumper Ways. Samsung Google Nexus S i9020 usb charging solution, Samsung Google Nexus S i9020 usb not recognised not detected

Samsung Young 2 SM-G130H Power On Off Key Jumper, Track, Ways Samsung Young 2 SM-G130H On Samsung Young 2 SM-G130H In the power ON-OFF, other than it is in the matrix keyboard flex is also connected to the keyboard filter IC. The solution below shows the connection line paths of the power key, this is useful without changing the filter IC and this can be used without having to connect the power key filter IC.

Diagram solution for nokia asha 311 speaker problem, if problem not solved by changing speaker then we can trace speaker points on motherboard with help of diagram. follow the diagram below and apply jumpers like diagram.

In Nokia Asha 200 Mic Problem can occur because of the faulty Microphone or it’s bad connection to the Cell Phone’s Motherboard. Bad connections can happen for many reasons like if it’s dropped or got wet, bad connection may also happen because of Carbon, Rust or even Dirt. So first of all you should clean Nokia Asha 200 Mic Ways and Motherboard of the Mobile Phone.

When we switch on mobile its not shows any thing on screen because lcd light not working.To solve this problem first check lcd or replace ldc with new one then check display light ic and other components related to light ic.In this post i share a diagram for nokia 105 lcd light solution, make jumper like diagram as shown below and chech mobile on power supply first then battery.

iphone 5 not charging problem, fake charging problem, iphone 5 charging error problem. To solve charging problem in iphone 5 first check charger to other iphone mobile, if charger is ok then disassemble iphone 5 and remove usb controler ic as shown below diagram and do jumper like diagram.

Nokia Asha 206 Charging Not Save Problem Nokia Asha 206 Charging Jeck Point Jumper  Here Nokia Ahsa 206 Diagram Shows The Point Below

Nokia 1280 display light jumper solution Nokia 1280 full display ways jumper 1280 white lcd problem solution

Nokia e5-00 rx and tx position

Solution: Try to changr light ic if  light ic not available then make jumpers like diagram below.Please try observe diagram carefully and try this trick your own risk

if you are facing problems like hanging freezing then soft reset can solve your problem.Soft reset will erase your personal data and applications installed on phone.Before do soft reset take backup of your important data first. Now you are going to reset your nokia lumia 625 mobile. Select settings>about>select reset Hard Reset: Hard reset is performed to reset mobile settings to orignal default settings.Take backup of important data before hard reset. Make sure your mobile battery is full or charger is connected to mobile. Turn off  nokia lumia 625 then press and hold volume down+camera+power keys together. Vhen phone vibraye release power button only. Hold volume down+camera keys for 6 to 7 seconds then release.

Problems :A lways show hands free logo on screen,no sound in ringer Solutions: Please before apply this work clean and heat red marked check its parts on pcb.then replace or remove usb and change hands free switching risistance near the usb connector cearfully. These jumper are fully tested by me and its me creation please tell me if you solve your problems.  

Solutions :First clean and heat usb connector if problem not solved then remove this and clean usb connector point with petrol or ctc(carbon tetra cleaner).This is solution one if Not Solved then try to repair with solution two.  Here is solution two witch is 10000000000000000000000% tested by me . Try to make direct jumper on black hands free switcher risistanse witch is red circule marked on pcb

 Problems:low Signal,No network,Searching network always. Solutions:please remove pa and make jumpers directly as this picture shown below with jumper wire.

Solutions: Please before apply this work clean and heat red marked check its parts on pcb.then replace or remove usb and change hands free switching risistance near the usb connector cearfully. These jumper are fully tested by me and its me creation please tell me if you solve your problems. i am waiting your coments.

use orignal charger and batrye if problem not solved then make these jumper as picture show bellow cearfully red line start from usb connector to charging ic stage of pcb its tested by me 100%you can try its at your own risk

Solutions.               First check polarity mising key on pcb key pad touch in dondition of no polarity of check meter then conform that key pad ic if its broken or missing try to remove key pad ic first replace with new if new key pad ic not available or broken links on pcb then make these jumpers cearfully and do not short with nearest key.these jumper can makes with smd reworkstation soldring iron.these jumper are so closest and you need to care for missing or shorting jumpers wire.please be cearfull.